- 您现在的位置：买卖IC网 > Sheet目录299 > 71M6545-IGT/F (Maxim Integrated)IC ENERGY METERING
71M6545/71M6545H Data Sheet
6.8.2
71M6545/H Analog Pins
Table 99 lists the analog pins. Pin types: O = Output, I = Input. The circuit number denotes the
equivalent circuit, as specified in 6.8.4 .
Table 99: 71M6545/H Analog Pins
Pin
No.
57
56
44
43
42
41
40
39
54
53
52
58
48
49
Name
IADC0
IADC1
IADC2
IADC3
IADC4
IADC5
IADC6
IADC7
VADC8 (VA)
VADC9 (VB)
VADC10 (VC)
VREF
XIN
XOUT
Type
I
I
O
I
O
Circuit
6
6
9
8
Description
Differential or single-ended Analog Line Current Sense Inputs:
These pins are voltage inputs to the internal A/D converter.
Typically, they are connected to the outputs of current
sensors. Unused pins must be tied to V3P3A .
When configured as differential inputs (i.e., by setting the
DIFFx_E control bits, where x=0, 2, 4, 6), pins are paired to form
differential inputs pairs: IADC0-IADC1, IADC2-IADC3, IADC4-
IADC5, and IADC6-IADC7.
IADC2-IADC3, IADC4-IADC5 and IADC6-IADC7 may be
configured for communication with the 71M6xx3 remote
isolated sensor interface (i.e., by setting the RMTx_E control
bits, where x=2, 4, 6). When configured as remote sensor
interfaces, these pins form balanced digital pairs for bi-
directional digital communications with a 71M6xx3 remote
isolated sensor.
Line Voltage Sense Inputs: These pins are voltage inputs to
the internal A/D converter. Typically, they are connected to
the outputs of resistor dividers. Unused pins must be tied to
V3P3A.
Voltage Reference for the ADC. This pin must be left
unconnected (floating). The VREF pin must be kept turned off
for normal operation (see VREF_CAL , I/O RAM 0x2704[7] ).
Crystal Inputs: A 32 kHz crystal should be connected across
these pins. Typically, a 15 pF capacitor is also connected
from XIN to GNDA and a 10 pF capacitor is connected from
XOUT to GNDA. It is important to minimize the capacitance
between these pins. See the crystal manufacturer datasheet for
details. If an external clock is used, a 150 mV (p-p) clock
signal should be applied to XIN, and XOUT should be left
unconnected.
128
v2
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
720-10007-00300
CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025
CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300
CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300
CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881
8 POS T/P SHLD 4 GR ASSY
7250B
PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200
CBL DSUB HD 15FEMAL-15MALE 2.0M
73304-111
MJ HOR ESMT 8/8 H/O T&R
相关代理商/技术参数
71M6545-IGTR/F
功能描述:计量片上系统 - SoC Metrology Proc. (3P 64K Flsh .1%)
RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6545T-IGT/F
制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube
71M6545T-IGTR/F
制造商:Maxim Integrated Products 功能描述:3-PHASE AFE, 32KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6601
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IF
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL/F
功能描述:模数转换器 - ADC Isolated Sensor IC
RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
71M6601-ILF
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring